baymavi - vevobahis - mobilbahis - https://guncelgirisi.com/. instagram takipçi satın al - instagram takipçi satın al mobil ödeme

Announcement

Collapse
No announcement yet.

F3-12800CL9-4GBRL running at 1333 mhz, not 1600 mhz

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • F3-12800CL9-4GBRL running at 1333 mhz, not 1600 mhz

    GSKILL Support,

    I am in need of your help. I just assembled a new build using four of the F3-12800CL9-4GBRL chips and while the system recognizes all of the chips, it is recognizing them @ 1333mhz, not the expected 1600mhz. the system is also rather unstable when trying to utilize large amounts of ram, however memtest completed successfully.

    System Info:

    16gb (4 DIMMs) F3-12800CL9-4GBRL RAM
    Asus P8P67 Pro motherboard running 1240 bios rev
    intel i7-2600k cpu
    Windows 7 Ultimate x64
    1.5V DRAM


    Thanks in advance!


    -Chris

  • #2
    anyone? bueler?

    Comment


    • #3
      The BIOS is defaulting to 1333, need to set it up to 1600, can do it through XMP


      Pls offer comments on support I provide, HERE, in order to help me do a better job here:

      Tman

      Comment


      • #4
        when i do that via XMP, the system becomes unstable and sometimes only recognizes 8gb ram or will hang..


        thoughts?

        Comment


        • #5
          May have to add a bit of voltage to the DRAM itself .02 to .04


          Pls offer comments on support I provide, HERE, in order to help me do a better job here:

          Tman

          Comment


          • #6
            I has exactly the same issue juste a few topics under, do i have to do the same thing? I don't nknow anything about voltage, what you suggest is eally safe?

            Comment


            • #7
              ok. XMP @ 1600 mhz with voltage @ 1.54v. seems stable but SPD max bandwidth still reporting as pc3-10700 (667mhz)

              is this correct?

              Comment


              • #8
                Might get the new version of CPU-Z and see what it shows it will show base frequency so if set up for 1600 should show 800 in the memory tab.

                Comment


                • #9
                  Originally posted by grayca View Post
                  ok. XMP @ 1600 mhz with voltage @ 1.54v. seems stable but SPD max bandwidth still reporting as pc3-10700 (667mhz)

                  is this correct?
                  That is correct, and it will never change. You need to look in the memory tab of CPU-z, those are the actual current operating values.

                  DRAM Frequency should show ~800MHz, 9-9-9-24.

                  Thank you
                  GSKILL TECH

                  Comment


                  • #10
                    Thank you. I think it's all workign right and stable now. Much appreciated.

                    Comment


                    • #11
                      I'm sorry to post here again, mais but i still have the same problem, and have exactl the same config that grayca, but i don't have a pro p8p67.

                      i tried to put 1.54v on the ram, it worked, first, but then after several boots, i had boot failure, and the voltage put itself in auto.

                      I don't understand what mistake i did. I didn't put manually the timing, there were writen, and were the right one.

                      What can i do?

                      Comment


                      • #12
                        Same thing as everybody else, input the settings for your memory, then see how it works.

                        If you have a problem, create a new thread with your hardware specs so we can help troubleshoot.

                        Thank you
                        GSKILL TECH

                        Comment


                        • #13
                          OK thank you! But i mad a topic, which is lost in the third ou fourth page i think!

                          Here!

                          http://www.gskill.us/forum/showthread.php?t=7570
                          Last edited by Iwao; 02-03-2011, 11:53 PM.

                          Comment

                          Working...
                          X