No announcement yet.

Rampage Gene II with F3-12800CL9T2-24GBRL Settings

  • Filter
  • Time
  • Show
Clear All
new posts

  • Rampage Gene II with F3-12800CL9T2-24GBRL Settings

    Rampage Gene II with F3-12800CL9T2-24GBRL Settings My CPU is the I7 920.
    Looking for the best settings for this memory currently it is running at 1600MHZ but I wanted to see if its possible to OC more or if I am running with the best settings. I have the latest bios from Asus installed. Is it possible to run this at 1800MHZ? I replaced G.SKILL Perfect Storm 6GB (3 x 2GB) 240-Pin DDR3 SDRAM DDR3 2000 (PC3 16000) Desktop Memory Model F3-16000CL8T-6GBPS never was able to get this kit to 2000MHZ. I haven't tried sense but I think the 24GBS is an improvement. Let me know if you think its an improvement over the 6GB kit.

    AI overclock - manual
    OC from CPU level up - auto
    OC from Memory level up - DDR3-1600
    CPU Ratio setting - 20 for 3.3GHz
    CPU Turbo Power Limit - disable

    CPU configuration
    CPU Ratio Setting - whichever you chose above
    C1E Support - disable
    Hardware prefetcher - enable
    Adjacent Cache line prefetcher - enable
    Intel Virtualization tech - disabled
    CPU TM Function - disable
    Execute Disabled bit - disabled
    Intel HT Technology - disable
    Active Processor Cores - all
    A20M - disabled
    Intel C-STATE tech - disabled

    BCLK frequency - 200
    PCIE frequency - 100
    DRAM frequency - 1600MHZ
    UCLK frequency - Auto
    QPI frequency - auto

    Dram Timing Control
    DRAM CAS# Latency - 9
    DRAM RAS# to CAS# Delay - 9
    DRAM RAS# PRE Time - 9
    DRAM RAS# ACT Time - 24

    DRAM Timing Mode - 2N
    All others are on AUTO

    EPU II Phase Control - Full Phase
    Load-line calibration - enable
    CPU differential amplitude - auto
    Extreme OV - disabled

    CPU voltage - Auto
    CPU PLL voltage - AUTO
    QPI-DRAM voltage - AUTO

    IOH voltage - AUTO
    IOH PCIE voltage - AUTO
    ICH voltage- AUTO
    ICH PCIE voltage - AUTO

    DRAM Bus voltage Auto

    CPU spread spectrum - disabled
    PCIE spectrum - disabled
    CPU clock skew - auto
    IOH clock skew - auto

    Any help or advice would be great! Thank you.

  • #2
    Try it at 1866 10-10-10-26, 2T, DRAM Voltage 1.6, and raise QPI/VTT voltage + .1 - if that works and is stable could try tightening the timings but doubt if you'd see a difference

    Pls offer comments on support I provide, HERE, in order to help me do a better job here:



    • #3
      Thank you Tman!! I will give it a go tonight and report back. What should I start the QPi/VTT voltage at?


      • #4
        Good news tried these timings here DDR3-1866 9-10-9-28 1.65V. Running super smooth. The QPI vtt voltage is set to auto at this time and the CPU is overclocked to 3.7GHz the Ram is flying I might add!! If you would like I can post all my settings. Thanks for the help.


        • #5
          Sounds good, actually great, and sure post the settings, it will prob help others, Thanx

          Pls offer comments on support I provide, HERE, in order to help me do a better job here: