-F3-10666CL7D-4GBXH 2 kits
-P8P67 Deluxe rev.3 Bios 1305
-Intel i7 2600k
-psu Antec TP 750w
Hallo to all, I write from Italy, so excuse me for my English.
Show my problem:
I've just builded my new PC (P8P67 deluxe, i7 2600k and 2 kits F3-10666CL7D-4GBXH) and the system won't boot with all slots populated ...it stops boot immediately with Qcode 45. I tried with MemOk and nothing changes, so I tried putting only one stick (2Gb) in each slot and in B2 position and the system boots. Reading in this forum i tried to enable XMP in the Overclock section of the bios and doing so the bios shows the correct latencies of the stick, otherwise by default it showed 9-9-8-24 etc.etc.
After this change the system boots with two sticks in channel B (sometimes it stops in the
"fail overclocking press F1 to change setting" and when I put sricks in slots of channel A the same issue Qcode 45 returns. I tried also to boot with only a stick in A2, or A1, or A1+A2 ....nothing it stops immediately on Qcode 45!! i've tested one by one the 4 stick in B2
and all of them boots OK, so I think the modules are good.
Then I resume:
-4 sticks full channels A1+A2+B1+B2 no boot Qcode 45
-1 or two sticks in A1 or A2 no boot Qcode 45
-1 stick in A2 and 1 in B2 like says the manual no boot Qcode 45
-1 stick in B2 boot OK
-XMP enabled 2 sticks in B1 + B2 boots (but sometimes ask for F1 -overclock failed-)
-any stick in channel A (single or with channel B) no boot Qcode 45
-I runned many times the MemOk without results.
please Help me.
ros
-P8P67 Deluxe rev.3 Bios 1305
-Intel i7 2600k
-psu Antec TP 750w
Hallo to all, I write from Italy, so excuse me for my English.
Show my problem:
I've just builded my new PC (P8P67 deluxe, i7 2600k and 2 kits F3-10666CL7D-4GBXH) and the system won't boot with all slots populated ...it stops boot immediately with Qcode 45. I tried with MemOk and nothing changes, so I tried putting only one stick (2Gb) in each slot and in B2 position and the system boots. Reading in this forum i tried to enable XMP in the Overclock section of the bios and doing so the bios shows the correct latencies of the stick, otherwise by default it showed 9-9-8-24 etc.etc.
After this change the system boots with two sticks in channel B (sometimes it stops in the
"fail overclocking press F1 to change setting" and when I put sricks in slots of channel A the same issue Qcode 45 returns. I tried also to boot with only a stick in A2, or A1, or A1+A2 ....nothing it stops immediately on Qcode 45!! i've tested one by one the 4 stick in B2
and all of them boots OK, so I think the modules are good.
Then I resume:
-4 sticks full channels A1+A2+B1+B2 no boot Qcode 45
-1 or two sticks in A1 or A2 no boot Qcode 45
-1 stick in A2 and 1 in B2 like says the manual no boot Qcode 45
-1 stick in B2 boot OK
-XMP enabled 2 sticks in B1 + B2 boots (but sometimes ask for F1 -overclock failed-)
-any stick in channel A (single or with channel B) no boot Qcode 45
-I runned many times the MemOk without results.
please Help me.
ros
Comment