Have 2 bad sticks of ddr3?

[animaluc]

memtest had both sticks fail in b1 slot. but they both passed in tests in a1 slot.

running on the one that had less errors and so far no problems.

error after 1 complete test with both sticks

AMD Phenom II X6 1075T Thuban 3.0GHz Socket AM3 125W Six-Core Desktop Processor
ASUS M4A78T-E AM3 AMD 790GX HDMI ATX AMD Motherboard
G.SKILL Flare 4GB (2 x 2GB) 240-Pin DDR3 SDRAM DDR3 1800 (PC3 14400) Desktop Memory Model F3-14400CL9D-4GBFLS
Rosewill Green Series RG700-S12 700W Continuous @40?C,80 PLUS Certified,Single 12V Rail,Active PFC"Compatible with Core i7, i5" Power Supply PSU
Microsoft WINDOWS 7 Home Premium FULL 64-bit
Sapphire 100287L Radeon HD 5670 Graphics Card - PCI Express 2.1 x16 - 512 MB GDDR5 SDRAM 2560 x 1600 - CrossFireX





took b1 out and ran a full test. a1 passed. removed a1 stick and ran b1 stick in a1 slot. it passed.

took b1 ran full test in b1slot it had 337 errors.



took a1 put it in b1 slot had 89 errors.



both in the #7 test range of memtest 86 v 4.10

[animaluc]

not one problem so far without other stick

the last bsod info I got.

KMODE_EXCEPTION_NOT_HANDLED (1e)
This is a very common bugcheck. Usually the exception address pinpoints
the driver/function that caused the problem. Always note this address
as well as the link date of the driver/image that contains this address.
Arguments:
Arg1: ffffffffc0000005, The exception code that was not handled
Arg2: 0000000000000000, The address that the exception occurred at
Arg3: 0000000000000008, Parameter 0 of the exception
Arg4: 0000000000000000, Parameter 1 of the exception

Debugging Details:
------------------


EXCEPTION_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

FAULTING_IP:
+3732306261336265
00000000`00000000 ?? ???

EXCEPTION_PARAMETER1: 0000000000000008

EXCEPTION_PARAMETER2: 0000000000000000

WRITE_ADDRESS: GetPointerFromAddress: unable to read from fffff800030cc100
0000000000000000

ERROR_CODE: (NTSTATUS) 0xc0000005 - The instruction at 0x%08lx referenced memory at 0x%08lx. The memory could not be %s.

BUGCHECK_STR: 0x1E_c0000005

CUSTOMER_CRASH_COUNT: 1

DEFAULT_BUCKET_ID: VISTA_DRIVER_FAULT

PROCESS_NAME: spoolsv.exe

CURRENT_IRQL: 0

TRAP_FRAME: fffff880089e9380 -- (.trap 0xfffff880089e9380)
NOTE: The trap frame does not contain all registers.
Some register values may be zeroed or incorrect.
rax=ffffffffffffffff rbx=0000000000000000 rcx=000000000000c93f
rdx=fffff88001c4d280 rsi=0000000000000000 rdi=0000000000000000
rip=0000000000000000 rsp=fffff880089e9511 rbp=fffff880089e9618
r8=ffffffffffffffff r9=0000000001ffffff r10=fffff800030cc908
r11=0000000000000001 r12=0000000000000000 r13=0000000000000000
r14=0000000000000000 r15=0000000000000000
iopl=0 nv up ei pl zr na po nc
00000000`00000000 ?? ???
Resetting default scope

UNALIGNED_STACK_POINTER: fffff880089e9511

LAST_CONTROL_TRANSFER: from fffff80002ee85d8 to fffff80002e9cd00


some better snap shots.


NB Voltage 1.4 in bios but really is 1.3 I think but shows up in turbo as 1.1

[animaluc]

running faster browsing it seems

one stick of ram and I maxed out the factory cpu spec which is 3.5 fro the cpu. if my ram ran right I can do 4050mhz.

[Tradesman]

Have you tried CR at 2

[animaluc]

yes, 9-9-9-24-41@2t.
had many bsods so I changed to 8-8-8-24-41@1t. not as bad

[Tradesman]

Next would be to raise CPU/NB maybe .05 to start, then if it helps or stable can further adjust from there raise or lower at .01 increments

[GSKILL TECH]

CPU-NB Voltage 1.4125 is high. You should lower this and work up from 1.20V. NB Voltage is suppose to be 1.10V, so that is fine.

For CL8, you should try DDR3-1800 8-9-8-24 1.66V up to 1.70V.

Thank you
GSKILL TECH