DDR3 and EP45T-UD3P

[Tradesman]

What's your RAM tRFC timing at? If lower than 54, might try raising it to 54 and/or up in 2 digit increments?

[ep45t-extreme]

BIOS SETTING WHEN TRYING TO CLOCK TO 3.2GHZ

MB Intelligent Tweaker(M.I.T.)
Robust Graphics Booster ...............: Auto
CPU Clock Ratio ..........................: x8
Fine CPU Clock Ratio.....................:.HAVENT GOT
CPU Frequency ...........................: 3.20ghz (400X8)

Clock Chip Control
Standard Clock Control
CPU Host Clock Control..................: [Enabled]
CPU Host Frequency (Mhz) ............: 400 Mhz
PCI Express Frequency (Mhz) .........:100
C.I.A.2 .................................:[Disabled]

Advanced Clock Control [Press Enter]
CPU Clock Drive...........................: <<< 800
PCI Express Clock Drive.................: <<< 900
CPU Clock Skew (ps)....................: 0
MCH Clock Skew (ps)...................: 0

DRAM Performance Control
Performance Enhance...................: [STANDARD]
Extreme Memory Profile (X.M.P.).....: Disabled
(G)MCH Frequency Latch...............: [Auto]
System Memory Multiplier ..............: AUTO
Memory Frequency (Mhz) ..............: 1600mhz
DRAM Timing Selectable ................: [AUTO]
Standard Timing Control
CAS Latency Time........................ 9
tRCD ......................................... 9
tRP'...........................................9
tRAS.......................................... 24

Advanced Timing Control
tRRD........................................... 4 (AUTO)
tWTR.......................................... 5 (AUTO)
tWR............................................ 10 (AUTO)
tRFC........................................... 74 (AUTO)
tRTP........................................... 5 (AUTO)
Command Rate (CMD) ....................:0 (AUTO)
Driving Strength Profiles
Driving Strength ............................
Channel A
Static tRead Value.........................:6 (AUTO)
tRD Phase0 Adjustment...................: 0 (Auto)
tRD Phase1 Adjustment...................: 1 (Auto)
tRD Phase2 Adjustment .................: 0 (Auto)
tRD Phase3 Adjustment..................: 0 (Auto)
Trd2rd(Different Rank)....................: 9 (Auto)
Twr2wr(Different Rank)...................: 7 (Auto)
Twr2rd(Different Rank)...................: 7 (Auto)
Trd2wr(Same/Diff Rank)..................: 9 (Auto)
Dimm1 Clock Skew Control...............:HAVENT GOT
Dimm2 Clock Skew Control...............:HAVENT GOT
Channel B
Static tRead Value.........................:6 (AUTO)
tRD Phase0 Adjustment...................: 0 (AUTO)
tRD Phase1 Adjustment...................: 1 (AUTO)
tRD Phase2 Adjustment .................: 0 (AUTO)
tRD Phase3 Adjustment..................: 0 (AUTO)
Trd2rd(Different Rank)....................: 9 (AUTO)
Twr2wr(Different Rank)...................: 7 (AUTO)
Twr2rd(Different Rank)...................: 7 (AUTO)
Trd2wr(Same/Diff Rank)..................: 9 (AUTO)
Dimm1 Clock Skew Control...............:AGAIN HAVENT GOT
Dimm2 Clock Skew Control...............:HAVENT GOT
Motherboard Voltage Control
CPU
CPU Vcore?.???....1.3250v.....................:1.36875 v
CPU Termination?..... 1.200V*.......:1.300V
CPU PLL???????....1.500V*.......AUTO)
MCH/ICH
MCH Core?????.....1.100V...........: (AUTO)
MCH Reference?.??.0.760V...........; (AUTO)
MCH/DRAM Ref.?......0.900V...........: HAVENT GOT
ICH I/O??????.....1.500V............: (AUTO)
ICH Core????...??1.100V............: HAVENT GOT
DRAM
DRAM Voltage ??....1.500V............: 1.580V
DRAM Termination .?0.750V............: 0.790V
Channel A Reference 0.750V............: (AUTO)
Channel B Reference 0.750V............: (AUTO)
Channel A Address VREF 750V (auto)
Channel B Address VREF 750V (auto)


try it now wont work
im sure they are the same settings i am putting in

[Tradesman]

tRFC maybe to 84