M4n78 se + f2-8800cl5d-4gbpi

[QuixMix]

I have the following configuration

Processor Athlon x 2 7750 2.7 Ghz
M4N78 SE
2 x 2GB F2-8800CL5D-4GBPI

I can only set it to 800 on this board?

How to config motherboard ? to 1066 or 1100 ?


Sorry my english is poor

[Tradesman]

Are you OCing at all? May require an OC and adjustments to some of the settings. Could you post your BIOS version and settings?

[QuixMix]

This information is enough?

Are you OCing at all? May require an OC and adjustments to some of the settings. Could you post your BIOS version and settings?

This information is enough?



General Information :
Manufacturer : American Megatrends Inc.
Version : 1105
Date : 09/11/2009 (mm/dd/yyyy)
Address : 1024 KB
Copyright : (C)2009 American Megatrends, Inc
Motherboard ID : 64-1105-000001-00101111-091109-MCP78D-A1258000
DMI Version : 2.5

Characteristics :
Flashable : Yes
Socketed : Yes

Functionality :
APM : Yes
ACPI : Yes
ESCD : Yes
PnP : Yes
PCI : Yes
ISA : Yes
AGP : No
USB : Yes
PCMCIA : No
Smart Battery : No

Boot Information :
Selectable Boot : Yes
CD-ROM Boot : Yes
PC Card (PCMCIA) Boot : No
I20 Boot : No
LS-120 Boot : Yes
1394 Boot : No
ATAPI ZIP Boot : Yes
Network Boot : No



General Information :
DIMM0 (BANK0 ) : 2048 MB - DIMM
DIMM1 (BANK1 ) : 2048 MB - DIMM

Information SPD EEPROM (DIMM0) :
Manufacturer : G Skill
Part Number : F2-8800CL5-2GBPI
Serial Number : Unspecified
Type : DDR2-SDRAM PC2-6400 (399 MHz) - [DDR2-800]
Format : Regular UDIMM (133,35 x 3)
Size : 2048 MB (2 ranks, 8 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : Yes
Width : 64-bit
Error Correction Capability (EC... No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 ?s, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : 2000
Supported Frequencies : 266 MHz, 400 MHz
CAS Latency (tCL) : 4 clocks @266 MHz, 5 clocks @400 MHz
RAS to CAS (tRCD) : 4 clocks @266 MHz, 5 clocks @400 MHz
RAS Precharge (tRP) : 4 clocks @266 MHz, 5 clocks @400 MHz
Cycle Time (tRAS) : 10 clocks @266 MHz, 15 clocks @400 MHz
Min TRC : 16 clocks @266 MHz, 24 clocks @400 MHz

EPP Profile #1 : Full Performance
Voltage Level : 1.9V
Address Command Rate : 2T
Cycle Time : 1.875ns @533.33 MHz
CAS Latency (tCL) : 5 clocks
RAS to CAS (tRCD) : 5 clocks
RAS Precharge (tRP) : 5 clocks
Cycle Time (tRAS) : 15 clocks
tRC : 48 clocks
tWR : 13 clocks

Information SPD EEPROM (DIMM1) :
Manufacturer : G Skill
Part Number : F2-8800CL5-2GBPI
Serial Number : Unspecified
Type : DDR2-SDRAM PC2-6400 (399 MHz) - [DDR2-800]
Format : Regular UDIMM (133,35 x 3)
Size : 2048 MB (2 ranks, 8 banks)
Module Buffered : No
Module Registered : No
Module SLi Ready (EPP) : Yes
Width : 64-bit
Error Correction Capability (EC... No
Max. Burst Length : 8
Refresh : Reduced (.5x)7.8 ?s, Self Refresh
Voltage : SSTL 1.8v
Prefetch Buffer : 4-bit
Manufacture : 2000
Supported Frequencies : 266 MHz, 400 MHz
CAS Latency (tCL) : 4 clocks @266 MHz, 5 clocks @400 MHz
RAS to CAS (tRCD) : 4 clocks @266 MHz, 5 clocks @400 MHz
RAS Precharge (tRP) : 4 clocks @266 MHz, 5 clocks @400 MHz
Cycle Time (tRAS) : 10 clocks @266 MHz, 15 clocks @400 MHz
Min TRC : 16 clocks @266 MHz, 24 clocks @400 MHz

EPP Profile #1 : Full Performance
Voltage Level : 1.9V
Address Command Rate : 2T
Cycle Time : 1.875ns @533.33 MHz
CAS Latency (tCL) : 5 clocks
RAS to CAS (tRCD) : 5 clocks
RAS Precharge (tRP) : 5 clocks
Cycle Time (tRAS) : 15 clocks
tRC : 48 clocks
tWR : 13 clocks

Memory Controller Information :
Memory Controller : System Memory
Location : Mainboard
Error Correction Capability : No
Number of connectors : 2
Max. Module Size : 8192 KB

[QuixMix]

Update to 1306 of bios

Update version from 1105 to 1306 of bios, in the bios change auto to 533 and save changes and start win 7 crash blue screen.

[QuixMix]

How to config please ? 2 x 2GB F2-8800CL5D-4GBPI

Update version from 1105 to 1306 of bios, in the bios change auto to 533 and save changes and start win 7 crash blue screen.

How to config please ?

[GSKILL TECH]

Post pictures of your BIOS and we can see what's going on.

Thank you
GSKILL TECH

[QuixMix]

Now in automatic mode

Post pictures of your BIOS and we can see what's going on.

Thank you
GSKILL TECH

Now in automatic mode, and is at 800 mhz max (sorry but do not have camera)


Sorry my english

[QuixMix]

My actual config

Multiplier 12
FSB 225

Freq processor 2.700 Mhz ( Athlon x2 7750 )

Freq ram 450mhz for CPU-z

[QuixMix]

My actual config part II

General Information :
Real Frequency : 2695.36 MHz
Multiplier : 11.5x
Northbridge Coeff. : 8x

Front Side Bus Information :
Bus Speed : 234.4 MHz
FSB Frequency : 2109.4 MHz

Initial Frequencies :
Frequency : 2300 MHz
Bus Speed : 200.00 MHz

Frequency Control :
Core #1 : 2695.33 MHz
Core #2 : 2695.40 MHz
Core #3 : 0.00 MHz
Core #4 : 0.00 MHz

Control Clock Frequency :
Type : None

Thermal Information :
Thermal Design Power : 68 W
Core Power : 79.69 W (estimated)
Resistance : 0.05 ?C/W (estimated)




NorthBridge Information :
Architecture : Northbridge
Manufacturer : AMD
Revision : 00
Multiplier : 8x
Bus Speed : 234.4 MHz
FSB Frequency : 2109.4 MHz
HyperTransport Clock : 1800 MHz
Upstream : 16-bit
Downstream : 16-bit
HTT max. Support : 2000 MHz
RAM max. Support : DDR2 (800 MHz)

NorthBridge Information :
Architecture : Northbridge
Manufacturer : AMD
Revision : 00
Multiplier : 8x
Bus Speed : 234.4 MHz
FSB Frequency : 2109.4 MHz
HyperTransport Clock : 1800 MHz
Upstream : 16-bit
Downstream : 16-bit
HTT max. Support : 2000 MHz
RAM max. Support : DDR2 (800 MHz)

Memory Information :
Type : DDR2-SDRAM PC2-7500
Frequency : 468.8 MHz
DRAM/FSB Ratio : 2/1
Supported Channels : Dual (128-bit)
Activated Channels : Dual
ECC Diagnostic : No
CAS Latency (tCL) : 5 clocks
RAS to CAS (tRCD) : 5 clocks
RAS Precharge (tRP) : 7 clocks
Cycle Time (tRAS) : 15 clocks
Bank Cycle Time (tRC) : 24 clocks
Command Rate : 2 T

[GSKILL TECH]

Looks like it is at DDR2-900, so you will need to increase CPU Host Frequency to 275 for DDR2-1100. Another method is to use the x5.33 multiplier. With this, you will need to set CPU Host Frequency to 207, and this will give you roughly DDR2-1103. Either way, just make sure CPU Ratio is set accordingly.

Thank you
GSKILL TECH

[QuixMix]

Please understand, my English is very basic

Looks like it is at DDR2-900, so you will need to increase CPU Host Frequency to 275 for DDR2-1100

And multiplier of processor ? Up to 275 appear this message :

Bad overclocking

Press F1 for enter to Bios Setup

Another method is to use the x5.33 multiplier. With this, you will need to set CPU Host Frequency to 207, and this will give you roughly DDR2-1103. Either way, just make sure CPU Ratio is set accordingly.

Processor multiplier to 5.33x ? 5.0x / 5.5x / 6.0x / to 35.0x x 207 is velocity of processor or memory to 533 ?

Please understand, my English is very basic




Uploaded with ImageShack.us



Uploaded with ImageShack.us

[GSKILL TECH]

Right now CPU multiplier and ratio is 234.4 x 11.5 = ~2695MHz

Instead, use 275 x 10 = CPU Frequency ~2750MHz

Using this and x4.00 memory multiplier = 275 x 4.00 = DDR2-1100

Also, try to overclock Northbridge Frequency and HyperTransport Clock to 2000MHz for better performance.

Thank you
GSKILL TECH