Bios RAM Configuration

[harold]

Hello,
Recently I did my first build with a
Motherboard: Asus p6x58D-E
CPU: i7 930
RAM: G.SKILL 6GB (3 x 2GB) 240-Pin DDR3 SDRAM DDR3 1600 (PC3 12800) Triple Channel Kit Desktop Memory Model F3-12800CL9T-6GBNQ

My ram only shows up at 2 gigs out of 6 gigs. Before it use to show randomly as 4 gigs and sometimes 6. It also shows my Ram speed as 1066. It has been running fine for a week. I tried to enable XMP Profile and it shows me my full 6 gigs at the 1600 speed however it increases my temperature by 5 degrees which I don't really like (Hopefully this means that my memory isn't defected). I don't plan to overclock my computer and prefer not overclock. All and just want stability even if the speed is at 1066. I also found a Bios template of what my layout looks like on Asus Bios from i4memory forums and was wondering if somebody could help me on what I should manually put in or suggest I should do.

Thanks,




****************************
AI Tweaker
****************************

Ai Overclock Tuner........... = [Manual]
CPU Ratio Setting............ = [20.0]
Xtreme Phase Full Power Mode. = [Enabled]
BCLK Frequency............... = [200]
PCIE Frequency............... = [100]
DRAM Frequency............... = [1603 Mhz]
UCLK Frequency............... = [3209 Mhz]
QPI Link Data Rate........... = [Auto]

CPU Voltage Control.......... = [Manual]
CPU Voltage.................. = [1.35000]
CPU PLL Voltage.............. = [1.80]
QPI/DRAM Core Voltage........ = [1.30000]
IOH Voltage.................. = [1.10]
IOH PCIE Voltage............. = [1.50]
ICH Voltage.................. = [1.10]
ICH PCIE Voltage............. = [1.50]
DRAM Bus Voltage............. = [1.66]
DRAM DATA REF Voltage on CHA. = [Auto]
DRAM CTRL REF Voltage on CHA. = [Auto]
DRAM DATA REF Voltage on CHB. = [Auto]
DRAM CTRL REF Voltage on CHB. = [Auto]
DRAM DATA REF Voltage on CHC. = [Auto]
DRAM CTRL REF Voltage on CHC. = [Auto]

Load-Line Calibration........ = [Disabled]
CPU Differential Amplitude... = [Auto try up to 1000mv for stability but may vary between individual cpus]
CPU Clock Skew............... = [Normal]
CPU Spread Spectrum.......... = [Disabled]
IOH Clock Skew............... = [Normal]
PCIE Spread Spectrum......... = [Disabled]

C1E Support.................. = [Enabled or Disabled]
Hardware Prefetcher.......... = [Enabled]
Adjacent Cache Line Prefetch. = [Enabled]
Intel(r) Virtualization Tech. = [Disabled]
CPU TM Function.............. = [Disabled]
Execute Disable Bit.......... = [Enabled]
Intel(r) HT Technology....... = [Enabled]
Active Processor Cores....... = [All]
A20M......................... = [Disabled]
Intel(r) SpeedStep(tm) Tech.. = [Enabled or Disabled]
Intel(r) C-STATE Tech........ = [Disabled]

*******************
DRAM Timing Control
*******************

1st Information:
DRAM CAS# Latency............ = [9]
DRAM RAS# to CAS# Delay...... = [9]
DRAM RAS# PRE Time........... = [9]
DRAM RAS# ACT Time........... = [24]
DRAM RAS# to RAS# Delay...... = [AUTO]
DRAM REF Cycle Time.......... = [110]
DRAM WRITE Recovery Time..... = [AUTO]
DRAM READ to PRE Time........ = [AUTO]
DRAM FOUR ACT WIN Time....... = [AUTO or 31 and higher]
DRAM Back-To-Back CAS# Delay. = [Auto]

2nd Information:
DRAM Timing Mode............. = [2N]
DRAM Round Trip Latency on CHA = [AUTO]
DRAM Round Trip Latency on CHB = [AUTO]
DRAM Round Trip Latency on CHC = [AUTO]

3rd Information:
DRAM WRITE To READ Delay (DD) = [AUTO]
DRAM WRITE To READ Delay (DR) = [AUTO]
DRAM WRITE To READ Delay (SR) = [AUTO]
DRAM READ To WRITE Delay (DD) = [AUTO]
DRAM READ To WRITE Delay (DR) = [AUTO]
DRAM READ To WRITE Delay (SR) = [AUTO]
DRAM READ To READ Delay (DD) = [AUTO]
DRAM READ To READ Delay (DR) = [AUTO]
DRAM READ To READ Delay (SR) = [AUTO]
DRAM WRITE to WRITE Delay (DD)= [AUTO]
DRAM WRITE to WRITE Delay (DR)= [AUTO]
DRAM WRITE to WRITE Delay (SR)= [AUTO]

Express Gate: Disabled

[GSKILL TECH]

Helping via email.

Thank you
GSKILL TECH