Very new at over clocking only OC 3 Mother Boards looking for some recommendations Please. Long post sorry. At 4.4 Ghz BCLK 100 Multiplier 44 Per Core all settings default V-Core 1.245v Off Set + 0.05v No BSOD or issues.
Issue with 4.5 V-Core 1.30v, or 4.6 GHz V Core 1.35v. LLC Auto or Ultra High at 140 Percent. On any other LLC settings.
BSOD B110A
Mother Board Asus Rampage 4 Black Edition
CPU: I 7 4930K at 4.5Ghz V-Core 1.30v
Heat Sink NH-D-14
LLC Ultra High at 140 Percent Seems High
V-Core 1.30v
Off Set + 0.50v Seems High
Memory G-Skill
F3-17000CL9Q-16GBZH
Series RipjawsZ
Memory Type DDR3
Capacity 16GB (4GBx4)
Multi-Channel Kit Quad Channel Kit
Tested Speed 2133MHz
Tested Latency 9-11-10-28-2N
Tested Voltage 1.65v
Registered/Unbuffered Unbuffered
Error Checking Non-ECC
SPD Speed 1600MHz
SPD Voltage 1.50v
Fan lncluded No
height 40 mm / 1.58 inch
Warranty Lifetime
Features Intel XMP (Extreme Memory Profile) Ready
At 4.5 Ghz with 2133 Mhz Mem I get a BSOD with a B110A
I think indicates a weak IMC on the CPU?
Is this correct?
VTT is used for Internal communications to the Chip Set.
VCCSA voltage basically talks to the memory controller.
Can I do this to the memory kit F3-17000CL9Q-16GBZH is 2133 MHz 16 Gb Kit
to lower the stress on the IMC. Appears have 2 options run 8 GBs of 2133 or 16 Gb at 1600 Mhz? Unless I am missing other settings could be adjusted?
F3-12800CL8Q-16GBZH
Series RipjawsZ
Memory Type DDR3
Capacity 16GB (4GBx4)
Multi-Channel Kit Quad Channel Kit
Tested Speed 1600MHz
Tested Latency 8-8-8-24-2N
Tested Voltage 1.50v
Registered/Unbuffered Unbuffered
Error Checking Non-ECC
SPD Speed 1600MHz
SPD Voltage 1.50v
Fan lncluded No
height 40 mm / 1.58 inch
Warranty Lifetime
Features Intel XMP (Extreme Memory Profile) Ready
Issue with 4.5 V-Core 1.30v, or 4.6 GHz V Core 1.35v. LLC Auto or Ultra High at 140 Percent. On any other LLC settings.
BSOD B110A
Mother Board Asus Rampage 4 Black Edition
CPU: I 7 4930K at 4.5Ghz V-Core 1.30v
Heat Sink NH-D-14
LLC Ultra High at 140 Percent Seems High
V-Core 1.30v
Off Set + 0.50v Seems High
Memory G-Skill
F3-17000CL9Q-16GBZH
Series RipjawsZ
Memory Type DDR3
Capacity 16GB (4GBx4)
Multi-Channel Kit Quad Channel Kit
Tested Speed 2133MHz
Tested Latency 9-11-10-28-2N
Tested Voltage 1.65v
Registered/Unbuffered Unbuffered
Error Checking Non-ECC
SPD Speed 1600MHz
SPD Voltage 1.50v
Fan lncluded No
height 40 mm / 1.58 inch
Warranty Lifetime
Features Intel XMP (Extreme Memory Profile) Ready
At 4.5 Ghz with 2133 Mhz Mem I get a BSOD with a B110A
I think indicates a weak IMC on the CPU?
Is this correct?
VTT is used for Internal communications to the Chip Set.
VCCSA voltage basically talks to the memory controller.
Can I do this to the memory kit F3-17000CL9Q-16GBZH is 2133 MHz 16 Gb Kit
to lower the stress on the IMC. Appears have 2 options run 8 GBs of 2133 or 16 Gb at 1600 Mhz? Unless I am missing other settings could be adjusted?
F3-12800CL8Q-16GBZH
Series RipjawsZ
Memory Type DDR3
Capacity 16GB (4GBx4)
Multi-Channel Kit Quad Channel Kit
Tested Speed 1600MHz
Tested Latency 8-8-8-24-2N
Tested Voltage 1.50v
Registered/Unbuffered Unbuffered
Error Checking Non-ECC
SPD Speed 1600MHz
SPD Voltage 1.50v
Fan lncluded No
height 40 mm / 1.58 inch
Warranty Lifetime
Features Intel XMP (Extreme Memory Profile) Ready
Comment