G.SKILL TECH FORUM

Go Back   G.SKILL TECH FORUM ? General Discussion ? Overclocking ? Intel Socket LGA 2011, 2011-v3, 2066

Intel Socket LGA 2011, 2011-v3, 2066 Intel i7, Extreme Series CPUs ~ Intel X79, X99, X299 chip sets

Reply
 
Thread Tools Search this Thread Display Modes
  #1  
Old 01-04-2015, 01:13 PM
JPG JPG is offline
Junior Member
 
Join Date: Dec 2014
Posts: 3
JPG is reading into overclocking
Default Issues Overclocking 64 GB of Trident X to 2400MHz on Rampage IV Black Edition + 4930K

I bought four 16 GB kits of Trident X memory (Serial Number: F3-2400C10-8GTX) not too long ago. I already realize that I should have just bought a 64 GB kit of Ripjaws Z, but it's too late for that now.

These kits run well at 2133MHz and 10-12-12-31-2 primary timings, but I get BSODs if I attempt to run at 2400MHz. The most common BSODs I get are MEMORY_MANAGEMENT, ATTEMPTED_TO_WRITE_READONLY_MEMORY, DRIVER_IRQL_NOT_LESS_OR_EQUAL, PFN_LIST CORRUPT, and PAGE_FAULT_IN_NON_PAGED_AREA. I don't know if this is relevant, but these BSODs are always caused by driver ntoskrnl.exe at address ntoskrnl.exe+150aa0. I tried a few passes of memtest, but I don't get any errors.

Is there any way to get all these kits stable, or am I wasting my time?
Reply With Quote
  #2  
Old 01-05-2015, 11:32 AM
GSKILL TECH's Avatar
GSKILL TECH GSKILL TECH is offline
Administrator
 
Join Date: Jul 2008
Location: Los Angeles, California
Posts: 12,956
GSKILL TECH has disabled reputation
Default

Did you manually set VCCSA Voltage?

Make sure 2 kits of RAM are installed in the same color slots.

You may need to raise timings for DDR3-2400 to work, or just lower DDR3-2133 timings to 9-11-11
__________________
Are you an overclocker? Have screen shots of your OC results? Please post and share your OC experience!

The new G.Skill Overclocking Section!

http://www.gskill.us/forum/forumdisplay.php?f=43
Reply With Quote
  #3  
Old 01-05-2015, 06:51 PM
JPG JPG is offline
Junior Member
 
Join Date: Dec 2014
Posts: 3
JPG is reading into overclocking
Default

Yes, I've tried setting the VCCSA up to 1.25V and 1.3V, and that gave me around 15 minutes at 2400MHz before one the BSODs I mentioned earlier happened. The 9-11-11 timings at 2133MHZ have been working fine for about 45 minutes as of this post. What should I try raising the 2400MHz timings to?
Reply With Quote
  #4  
Old 01-06-2015, 11:40 AM
GSKILL TECH's Avatar
GSKILL TECH GSKILL TECH is offline
Administrator
 
Join Date: Jul 2008
Location: Los Angeles, California
Posts: 12,956
GSKILL TECH has disabled reputation
Default

11-12-12 or you can try to add a little more DRAM Voltage to see if that can help.

You can also keep them at DDR3-2133 and try to lower timings. 9-11-11 or 10-11-11
__________________
Are you an overclocker? Have screen shots of your OC results? Please post and share your OC experience!

The new G.Skill Overclocking Section!

http://www.gskill.us/forum/forumdisplay.php?f=43
Reply With Quote
  #5  
Old 01-06-2015, 06:08 PM
JPG JPG is offline
Junior Member
 
Join Date: Dec 2014
Posts: 3
JPG is reading into overclocking
Default

I raised the voltage to 1.71V (2133 used about 1.68V) and tried the timings you suggested. They seem to be working, but is this a safe voltage to use all the time?
Reply With Quote
  #6  
Old 01-07-2015, 10:28 AM
GSKILL TECH's Avatar
GSKILL TECH GSKILL TECH is offline
Administrator
 
Join Date: Jul 2008
Location: Los Angeles, California
Posts: 12,956
GSKILL TECH has disabled reputation
Default

Yes, no problem.
__________________
Are you an overclocker? Have screen shots of your OC results? Please post and share your OC experience!

The new G.Skill Overclocking Section!

http://www.gskill.us/forum/forumdisplay.php?f=43
Reply With Quote
Reply

Bookmarks

Tags
4930k, rampage 4 black edition, trident x

Thread Tools Search this Thread
Search this Thread:

Advanced Search
Display Modes

Posting Rules
You may not post new threads
You may not post replies
You may not post attachments
You may not edit your posts

BB code is On
Smilies are On
[IMG] code is On
HTML code is On

Forum Jump


All times are GMT -8. The time now is 10:38 AM.


Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2017, Jelsoft Enterprises Ltd.
All rights reserved. Copyright 1989-2013, G.Skill International Enterprise