Announcement

Collapse
No announcement yet.

ASRock X79 Extreme4 + Intel 4930K + F3-19200CL10Q-32GBZHD +

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • ASRock X79 Extreme4 + Intel 4930K + F3-19200CL10Q-32GBZHD +

    First, sorry for my English. I have a problem in my hardware configuration. I searched here in the forum some similar problem, until I found, but it was discussed the possibility of poor contact. I disassembled and reassembled everything again and the problem persists.
    I followed steps as mentioned by the forum adminstrator (clear CMOS and select the XMP profile 1 and change the memory clock to 1333Mhz), but everything in it. http://www.gskill.us/forum/showthread.php?t=11138 I found a post in which the system was stable over time, but even then REBOOT and time alone recognizes the video and not hours.
    I am describing the whole system and sending attached my SETUP screens.

    1. INTEL BX80633I74930K
    2. G.SKILL Z SERIES 32GB (4X8GB) DDR3 2400MHZ PC319200 - F3-19200CL10Q-32GBZHD
    4. ASROCK X79 EXTREME4/A/ASR Updated BIOS V3.40
    5. ASUS DVD 24X SATA DRW-24F1ST/BLK/B/AS
    6. HD Seagate Barracuda 2TB 7200RPM 64MB SATA III - ST2000DM001
    7. VGA EVGA GeForce GTX780 SuperClocked 3GB DDR5 384-Bit PCI-Express 3.0 - 03G-P4-2783-KR
    8. ATX CORSAIR TX750
    9. WATERCOOLER CORSAIR H100I

    Screen 1:
    http://www.gskill.us/forum/picture.p...&pictureid=182

    Screen 2:
    http://www.gskill.us/forum/picture.p...&pictureid=181

    Screen 3:
    http://www.gskill.us/forum/picture.p...&pictureid=180

    Screen 4:
    http://www.gskill.us/forum/picture.p...&pictureid=179

    Screen 5:
    http://www.gskill.us/forum/picture.p...&pictureid=178

    Screen 6:
    http://www.gskill.us/forum/picture.p...&pictureid=177

    Screen 7:
    http://www.gskill.us/forum/picture.p...&pictureid=176

    Screen 8:
    http://www.gskill.us/forum/picture.p...&pictureid=175

    Screen 9:
    http://www.gskill.us/forum/picture.p...&pictureid=174

    Screen 10:
    http://www.gskill.us/forum/picture.p...&pictureid=173

    Screen 11:
    http://www.gskill.us/forum/picture.p...&pictureid=172

    Attention: These Screens were taken with reference to the post above where the system became more stable time.

  • #2
    DRAM Voltage should be 1.65V

    VCCSA Offset Voltage should be +0.250V or more for full slots. You may want to test each stick first to see if they pass.

    Comment


    • #3
      Hello,
      Unfortunately I'm not an overclocker. Actually just like to make my system work with the maximum performance obtained G.Kill RAMs running at 2400MHz (OC) and the i7 4930K.
      I am providing a new set of 1600Mhz RAMs (not OC) and another video card because a colleague commented that there could be incompatibility between these three: RAMs + 4930K + GTX 780.
      I doubt the possibility of being with the GTX 780, but I'm still waiting for the results and keep informed.

      Have on the performance of the screens, I could send yes, some advises more reliable program? I only use the v1.70 x64 CPUID to check Mhz and the timing of RAMs.
      Example, now gave clear CMOS and the CPU is working as advertised, the ADRs station as you can see, working with a frequency of 666.5Mhz, wrong right? You can check the log that this timing as described in the G.Kill web site.

      Awaiting the parts to make a new test, thanks.

      PS. The TXT file put in 4SHARED.

      Comment


      • #4
        Hello, good afternoon!
        Tested with a set of memories 1600mhz and another video card and it worked with the default (AUTO) settings.
        I disassembled everything again, and removed to the power cables. To my surprise it worked with the original configuration (EVGA GTX 780, ASRock X79 Extreme4 Intel 4930K + F3-19200CL10Q-32GBZHD (4x8)).
        Only I made the following configuration in the BIOS:
        1 - Clear CMOS
        2 - I put the XMP profile 1
        3 - Clock of 2133MHz memories
        4 - The rest all standard

        It worked perfectly exeto this velociodade q should be 2400MHz.
        When I select 2400MHz PC or the POST.

        Am I doing something wrong, or would some step you should do?

        Thank you!

        PS .: Tested separate memory module and it's all ok.

        Comment

        Working...
        X