 |
 |
    |
|
|||||||
| Overclocking All about memory overclocking, bandwidth results, tips/guides |
 |
|
|
Thread Tools | Search this Thread | Display Modes |
|
|
|
#1
06-13-2012, 02:00 PM
|
|||
|
|||
Xmp 1.3
Motherboard: asrock exreme9 x79
cpu: i7 3820 ram: G.SKILL Trident X Series 240-Pin DDR3 SDRAM DDR3 2400 everytime I activate xmp 1.3 profile in bios and try to reboot with saved setting I get a black screen and nothing happens. Any ideas why? Thanks for your time. 
|
|
#2
06-13-2012, 03:30 PM
|
|||
|
|||
|
anyone know?
|
|
#3
06-13-2012, 04:29 PM
|
||||
|
||||
|
My guess would be their BIOS isn't ready for XMP 1.3 at 2400, they only show a few 2400 sets and all are for 2 sticks, they also mention that 2400 sticks will run at 2133 - doesn't make a lot of sense to me, believe they only 'TEST' sticks at default (1333/1600). Might try the XMP 1.2 profile which is native for X79 or post your BIOS settings (DRAM timings, system voltages, what your OC is, etc)
__________________
   Pls offer comments on support I provide, HERE, in order to help me do a better job here: Tman Last edited by Tradesman; 07-24-2012 at 07:31 AM.
|
|
#4
06-18-2012, 10:19 AM
|
||||
|
||||
|
What is the VCCSA Voltage? This needs to be increased for DDR3-2400.
Thank you GSKILL TECH
__________________
Are you an overclocker? Have screen shots of your OC results? Please post and share your OC experience! The new G.Skill Overclocking Section! http://www.gskill.us/forum/forumdisplay.php?f=43
|
|
#5
06-18-2012, 01:05 PM
|
|||
|
|||
|
Hi thanks for your reply and concern. I looked into the bios and saw that the vccsa voltage was at 0.098v. Do you have any idea what it should be set to for 2400. Thank your sir.
|
|
#6
06-18-2012, 05:22 PM
|
||||
|
||||
|
Not sure how many sticks you have...maybe start at 1.2 then can drop or head up from there, 1.25 is normally enough for 4 sticks though some have needed a bit more
__________________
Pls offer comments on support I provide, HERE, in order to help me do a better job here: Tman
|
|
#7
06-18-2012, 08:13 PM
|
|||
|
|||
|
i ahve 2x 8gb sticks ill try it out and update u thanks for your time.
|
|
#9
06-18-2012, 09:00 PM
|
|||
|
|||
|
So i set it to xmp 1.3 and set vccsa to 1.2. After saving just a blank black screen and no boot. I dont know if that means i should increase vccsa
Last edited by HaLLuCiiNaTioN; 06-18-2012 at 10:06 PM.
|
|
#10
06-19-2012, 08:25 AM
|
||||
|
||||
|
Test one module at a time with just XMP to see if both can boot properly. Which slots do you have them installed in?
Thank you GSKILL TECH
__________________
Are you an overclocker? Have screen shots of your OC results? Please post and share your OC experience! The new G.Skill Overclocking Section! http://www.gskill.us/forum/forumdisplay.php?f=43
|
|
| Bookmarks |
«
Previous Thread
|
Next Thread
»
| Thread Tools | Search this Thread |
| Display Modes | |
Hybrid Mode
|
|
All times are GMT -8. The time now is 03:46 AM.