Announcement

Collapse
No announcement yet.

Memory 2133 Mhz BSOD B11OA Help Please

Collapse
X
 
  • Filter
  • Time
  • Show
Clear All
new posts

  • Memory 2133 Mhz BSOD B11OA Help Please

    Very new at over clocking only OC 3 Mother Boards looking for some recommendations Please. Long post sorry. At 4.4 Ghz BCLK 100 Multiplier 44 Per Core all settings default V-Core 1.245v Off Set + 0.05v No BSOD or issues.

    Issue with 4.5 V-Core 1.30v, or 4.6 GHz V Core 1.35v. LLC Auto or Ultra High at 140 Percent. On any other LLC settings.
    BSOD B110A

    Mother Board Asus Rampage 4 Black Edition
    CPU: I 7 4930K at 4.5Ghz V-Core 1.30v
    Heat Sink NH-D-14
    LLC Ultra High at 140 Percent Seems High
    V-Core 1.30v
    Off Set + 0.50v Seems High
    Memory G-Skill
    F3-17000CL9Q-16GBZH
    Series RipjawsZ
    Memory Type DDR3
    Capacity 16GB (4GBx4)
    Multi-Channel Kit Quad Channel Kit
    Tested Speed 2133MHz
    Tested Latency 9-11-10-28-2N
    Tested Voltage 1.65v
    Registered/Unbuffered Unbuffered
    Error Checking Non-ECC
    SPD Speed 1600MHz
    SPD Voltage 1.50v
    Fan lncluded No
    height 40 mm / 1.58 inch
    Warranty Lifetime
    Features Intel XMP (Extreme Memory Profile) Ready

    At 4.5 Ghz with 2133 Mhz Mem I get a BSOD with a B110A
    I think indicates a weak IMC on the CPU?

    Is this correct?
    VTT is used for Internal communications to the Chip Set.
    VCCSA voltage basically talks to the memory controller.

    Can I do this to the memory kit F3-17000CL9Q-16GBZH is 2133 MHz 16 Gb Kit
    to lower the stress on the IMC. Appears have 2 options run 8 GBs of 2133 or 16 Gb at 1600 Mhz? Unless I am missing other settings could be adjusted?

    F3-12800CL8Q-16GBZH
    Series RipjawsZ
    Memory Type DDR3
    Capacity 16GB (4GBx4)
    Multi-Channel Kit Quad Channel Kit
    Tested Speed 1600MHz
    Tested Latency 8-8-8-24-2N
    Tested Voltage 1.50v
    Registered/Unbuffered Unbuffered
    Error Checking Non-ECC
    SPD Speed 1600MHz
    SPD Voltage 1.50v
    Fan lncluded No
    height 40 mm / 1.58 inch
    Warranty Lifetime
    Features Intel XMP (Extreme Memory Profile) Ready

  • #2
    With Core Voltage on Normal (Not Off Set) can use Load Line Calibration at 120 Percent Normal and no BSOD codes.
    Last edited by Larry L; 04-04-2015, 07:23 PM.

    Comment


    • #3
      LLC does not need to be Ultra for ~4.5GHz

      IMC should be OK, I think the issue is stable Voltage for CPU.

      Comment


      • #4
        Changed the LLC from Ultra High to Medium at 120 Percent. Recommended maximum for 4.45 GHz.

        Per the guide listed here Thank You

        Comment

        Working...
        X