F3-16000CL9T-6GBPS + ASUS P6T / Deluxe / V2 BIOS settings

[GSKILL TECH]

These settings may also work for other packages such as the Trident Series, it is simply to operate DDR3-2000 on the ASUS P6T motherboards.


Ai Overclock Tuner - Manual
CPU Ratio Setting - 16
Intel SpeedStep Tech - Disabled
BCLK Frequency - 200
DRAM Frequency - DDR3-2000
UCLK Frequency - 4000MHz
QPI Link Data Rate - AUTO

DRAM Timing Control
CAS Latency - 9
tRCD - 9
tRP - 9
tRAS - 24
Command Rate - 2N

CPU Voltage - 1.30V
CPU PLL Voltage - 1.85V
QPI/DRAM Core Voltage - 1.50V
IOH Voltage - 1.35V
IOH PCIE Voltage - 1.6V
ICH Voltage - 1.20V
ICH PCIE Voltage - 1.60V
DRAM Bus Voltage - 1.66V

Load Line Calibration - Disabled



For DDR3-1866

Ai Overclock Tuner - Manual
CPU Ratio Setting - 15
Intel SpeedStep Tech - Disabled
BCLK Frequency - 186
DRAM Frequency - DDR3-1866
UCLK Frequency - 3732
QPI Link Data Rate - AUTO

DRAM Timing Control
CAS Latency - 9
tRCD - 9
tRP - 9
tRAS - 24
Command Rate - 2N

CPU Voltage - 1.30V
CPU PLL Voltage - 1.85V
QPI/DRAM Core Voltage - 1.30V
IOH Voltage - 1.35V
IOH PCIE Voltage - 1.6V
ICH Voltage - 1.20V
ICH PCIE Voltage - 1.60V
DRAM Bus Voltage - 1.66V

Load Line Calibration - Disabled


Thank you
GSKILL SUPPORT

[And Uh]

P6T Deluxe

The ASUS P6T Deluxe does not allow DRAM Bus Voltage of 1.65 volts - It's either 1.64 or 1.66 volts. My bios is currently version 1606

[Miquel]

I was try EXACTLY this config with no result (system reboots at start)

I can't use your memory over 1834 MHz.

Core i7 920 C0/C1
ASUS P6T DeLuxe
Windows 7 64 bits

Thank you

[GSKILL TECH]

Try increasing QPI/DRAM Voltage to 1.55V, your processor may be having a tough time reaching high enough to operate DDR3-2000.

If you have a good CPU Cooler, try increasing the CPU ratio setting to 18 to see if that will assist.

Thank you
GSKILL SUPPORT

[Tradesman]

Have you tried command rate at 2N?

[Miquel]

I have tried with QPI 1.55v and 2N command and still not working.

The system boots but restarts after windows 7 starting screen.

[Tradesman]

May have to raise tRFC a bit and/or raise tRAS to 27

[Miquel]

No way, still not working.

I tried:

27 - 72
27 - 88
27 - Auto
24 - 72
24 - 88
24 - Auto

[Tradesman]

Can you post screen shots of your BIOS settings?

[lovingbenji]

Hello guys,

First of, thank you for your kits, I use them since I am DDR2 and I have always been impressed by the quality

I have just bought the following configuration :

ASUS P6T Deluxe v2 [Bios 0504]
Intel Core i7 i920 - D0
6GB GSkill Trident PC12800 6-7-6-18 - 1.65V - F3-12800CL6T-6GBTD
OCZ Vertex 120Go [F/W 1.30] (System)
Velociraptor 10000tr 300Gb (Data)
Video ASUS GTX285
Son Audigy2 ZS
Antec P183
Alimentation Corsair HX850

And I would like to know what are the recommended bios settings for this memory and this motherboard in order to run it @ 800MHz (CPU @ 20*200).

Many thanks in advance,

- Ben

[GSKILL TECH]

Miquel,

The memory controller is embedded in your processor, you may have a processor that is unable to operate DDR3-2000. Post up screen shots of your BIOS and we'll see if we can tune some things.


lovingbenji,

BIOS settings would be same as above, but instead of 9-9-9-24, use 6-7-6-18. DDR3-2000 to DDR3-1600. And UCLK Frequency will only need to be 3200. It should look like this:

Ai Overclock Tuner - Manual
CPU Ratio Setting - 20
Intel SpeedStep Tech - Disabled
BCLK Frequency - 200
DRAM Frequency - DDR3-1600
UCLK Frequency - 3200MHz
QPI Link Data Rate - AUTO

DRAM Timing Control
CAS Latency - 6
tRCD - 7
tRP - 6
tRAS - 18
Command Rate - 1N

You will need to tune voltages accordingly.

Thank you
GSKILL SUPPORT

[lovingbenji]

Thx a lot for the very quick answer guys

[Miquel]

Can you post screen shots of your BIOS settings?

Download all my bios settings here

[Miquel]

I changed the C0 cpu for a D0 and everything runs smoothly.

Thank you.

[TPB]

Hello everybody,

I am a new G.Skill memory user and I would like to use its full potential (the BIOS default setting is 1333 MHz for the memory. Also, I am not very experienced with OC.

My configurations is as follow:
ASUS P6TD Deluxe [Bios 0501]
Intel Core i7 975 Extreme Edition - Noctua NH-D14
6GB GSkill Trident DDR3-2000 PC1600 9-9-9-24
System : Intel X25-M Mainstream - SSD 80 Go 2.5" 9.5 mm MLC
Software: Raid 0 - 2 Western Digital VelociRaptor 300 Go WD3000HLFS
Data: Raid 1 - 2 Western Digital Caviar Black 500 Go
Crossfire 2 Sapphire VAPOR-X HD 5870
Creative Sound Blaster X-Fi Titanium Fatal1ty Champion Series
Corsair Obsidian 800D
Corsair HX850W

The BIOS doesn't allow me to set the memory frequency to 2000 MHz and when I set a frequency higher than 1600 MHz the computer doesn't boot (error message display at the BIOS).

I will be grateful for any help about the BIOS settings in order to have some performance increase but keeping everything safe.
BR