Announcement

Collapse

UNDER CONSTRUCTION: G.Skill Forum

Hello Everyone

The G.Skill Technical forum will be under construction during the month of February. There may be random down time, so we sincerely appreciate your patience and cooperation during this time. We are excited to bring you a more interactive forum to share information. For any technical assistance or issue that may require more attention, please contact us directly via other methods such as email, telephone, social media, NewEgg Chat, and more. Support is available through any avenue you can reach us.

ustech@gskillusa.com
techsupport@gskill.com


We hope for a quick and smooth transition

Thank you for your understanding

GSKILL SUPPORT
See more
See less

Memory 2133 Mhz BSOD B11OA Help Please

Collapse
X
  • Filter
  • Time
  • Show
Clear All
new posts

  • Memory 2133 Mhz BSOD B11OA Help Please

    Very new at over clocking only OC 3 Mother Boards looking for some recommendations Please. Long post sorry. At 4.4 Ghz BCLK 100 Multiplier 44 Per Core all settings default V-Core 1.245v Off Set + 0.05v No BSOD or issues.

    Issue with 4.5 V-Core 1.30v, or 4.6 GHz V Core 1.35v. LLC Auto or Ultra High at 140 Percent. On any other LLC settings.
    BSOD B110A

    Mother Board Asus Rampage 4 Black Edition
    CPU: I 7 4930K at 4.5Ghz V-Core 1.30v
    Heat Sink NH-D-14
    LLC Ultra High at 140 Percent Seems High
    V-Core 1.30v
    Off Set + 0.50v Seems High
    Memory G-Skill
    F3-17000CL9Q-16GBZH
    Series RipjawsZ
    Memory Type DDR3
    Capacity 16GB (4GBx4)
    Multi-Channel Kit Quad Channel Kit
    Tested Speed 2133MHz
    Tested Latency 9-11-10-28-2N
    Tested Voltage 1.65v
    Registered/Unbuffered Unbuffered
    Error Checking Non-ECC
    SPD Speed 1600MHz
    SPD Voltage 1.50v
    Fan lncluded No
    height 40 mm / 1.58 inch
    Warranty Lifetime
    Features Intel XMP (Extreme Memory Profile) Ready

    At 4.5 Ghz with 2133 Mhz Mem I get a BSOD with a B110A
    I think indicates a weak IMC on the CPU?

    Is this correct?
    VTT is used for Internal communications to the Chip Set.
    VCCSA voltage basically talks to the memory controller.

    Can I do this to the memory kit F3-17000CL9Q-16GBZH is 2133 MHz 16 Gb Kit
    to lower the stress on the IMC. Appears have 2 options run 8 GBs of 2133 or 16 Gb at 1600 Mhz? Unless I am missing other settings could be adjusted?

    F3-12800CL8Q-16GBZH
    Series RipjawsZ
    Memory Type DDR3
    Capacity 16GB (4GBx4)
    Multi-Channel Kit Quad Channel Kit
    Tested Speed 1600MHz
    Tested Latency 8-8-8-24-2N
    Tested Voltage 1.50v
    Registered/Unbuffered Unbuffered
    Error Checking Non-ECC
    SPD Speed 1600MHz
    SPD Voltage 1.50v
    Fan lncluded No
    height 40 mm / 1.58 inch
    Warranty Lifetime
    Features Intel XMP (Extreme Memory Profile) Ready

  • #2
    With Core Voltage on Normal (Not Off Set) can use Load Line Calibration at 120 Percent Normal and no BSOD codes.
    Last edited by Larry L; 04-04-2015, 07:23 PM.

    Comment


    • #3
      LLC does not need to be Ultra for ~4.5GHz

      IMC should be OK, I think the issue is stable Voltage for CPU.
      Are you an overclocker? Have screen shots of your OC results? Please post and share your OC experience!

      The new G.Skill Overclocking Section!

      http://www.gskill.us/forum/forumdisplay.php?f=43

      Comment


      • #4
        Changed the LLC from Ultra High to Medium at 120 Percent. Recommended maximum for 4.45 GHz.

        Per the guide listed here Thank You

        Comment

        Working...
        X