[Ripjaws] F3-10666CL7D-4GBRH and Gigabyte GA-P55-UD3

[pmcalduff]

Is [Ripjaws] F3-10666CL7D-4GBRH memory compatible with the Gigabyte GA-P55-UD3 motherboard?

The reason I ask is because I recently upgraded my computer with:

Intel i7 860
Gigabyte GA-P55-UD3
[Ripjaws] F3-10666CL7D-4GBRH

I put it all together, reinstalled my OS and loaded the latest drivers (downloaded from the internet) for all of my hardware. I also checked and made sure that my BIOS is the latest version. However, in the morning when my computer is cold and I try to boot it up I get a Blue Screen of Death with the following ?Stop Code? and ?Error Message?:

PFN_LIST_CORRUPT
*** STOP: 0x0000004E (0x00000099, 0x000A1719, 0x00000004, 0x00000000)

This stop code is often associated with a memory problem.

Thank you in advanced.

Sincerely,

Paul

[GSKILL TECH]

Did you set the memory settings in BIOS? Should look something like this:

Advanced CPU Features:
CPU Clock Ratio ................................ [21x]
Intel(R) Turbo Boost Tech .................. [Disabled]
CPU Cores Enabled ............................ [All]
CPU Multi Threading .......................... [Enabled]
C3/C6/C7 State Support ................... [Auto]
CPU Enhanced Halt (C1E) ................... [Auto]
C3/C6/C7 State Support .................... [Auto]
CPU Thermal Monitor ......................... [Auto]
CPU EIST Function ............................ [Disabled]
Virtualization Technology ................... [Disabled]
Bi-Directional PROCHOT ..................... [Auto]


Uncore & QPI Features:
QPI Clock Ratio ...........................................AUTO
QPI Link Speed .............................. AUTO
Uncore Clock Ratio...........................AUTO
Uncore Frequency .......................... AUTO
Isonchronous Frequency ..................[Enabled]


Standard Clock Control:
Base Clock (BCLK) Control ................ [Enabled]
BCLK Frequency (MHz) ..................... 133
PCI Express Frequency (MHz) ........... [100]

C.I.A.2 [Disabled]

Advanced Clock Control:
CPU Clock Drive ..............................[800mV]
PCI Express Clock Drive ................... [900mV]
CPU Clock Skew ............................. [0ps]


Advanced DRAM Features:
Extreme Memory Profile (X.M.P) ......... [Disabled]
System Memory Multiplier (SPD) ........ [10.0] (choices are Auto/6/8/10)
Performance Enhance ...................... [Standard]
DRAM Timing Selectable (SPD) .......... [Expert]

Channel A + B + C

Channel A Timing Settings:
##Channel A Standard Timing Control##
CAS Latency Time ...................... 7
tRCD ....................................... 7
tRP ......................................... 7
tRAS ....................................... 24

##Channel A Advanced Timing Control##

Command Rate (CMD) ................ 2

Advanced Voltage Control:

CPU
Load Line Calibration ................. [Disabled]
CPU Vcore ............................... 1.275 [1.275V]
QPI/VTT Voltage 1.150v ............ 1.100V [1.100V]
CPU PLL 1.800v ....................... 1.800v [1.800V]

DRAM
DRAM Voltage 1.500v .............. 1.500V
DRAM Termination 0.750v [AUTO]
Ch-A Data VRef. 0.750v [AUTO]
Ch-B Data VRef. 0.750v [AUTO]
Ch-A Address VRef. 0.750v [AUTO]
Ch-B Address VRef. 0.750v [AUTO]

Save and exit.

Thank you
GSKILL SUPPORT

[pmcalduff]

Thank you for your quick response.

I tried the memory both at is default settings and using the XMP profile.
I did this both in "fail safe" and in "optimized" mode.

I haven?t touched any of the settings you mentioned.

By the way, I don?t really want to disable turbo mode. I spend a lot of extra money to get a CPU with that feature. Is that necessary to do this to get this memory to work in on mobo? ?Intel(R) Turbo Boost Tech .................. [Disabled]?

[Tradesman]

Do you have the proper RAM voltage and a command rate of 2T?

[pmcalduff]

Thank you again for your quick response.

The Profile DDR Voltage is 1.5V (which is correct.)
The Profile QPI Voltage is 1.1V (I don't know if this is correct or not.)

Using XMP - Profile 1 the Command Rate (CMD) is "2" with it set to "Auto".
Disabling XMP the Command Rate (CMD) is "1" with it set to "Auto".

Paul

[GSKILL TECH]

With those settings, are you still getting that error? Try testing them individually to make sure you don't have a bad stick.

Thank you
GSKILL SUPPORT